|
The UK's largest distributor of display
shrink wrap and shrink wrapping machinery
|
Chamber/ Seal & Shrink Machines
» View
Shrink Wrap Machines
|
|
|
Shrink Wrap
Machinery | Shrink
Wrap Films |
Polyolefin Shrink Films
|
|
|
|
|
|
Shrink Wrap
> Shrink Wrap Machines
> Shrink Wrap Machinery
An Introduction to Shrink Wrap Machinery
The shrink
wrap process involves two stages - the enveloping of the pack in shrink
wrap either totally or partially and - the application of heat to the film which
activates the material's memory of its non-stretched molecular chains.
The application of
shrink wrap film can be divided into two principal types - transit and display.
The purpose of
transit packaging is to offer the lowest cost option for packaging. The
material used is almost exclusively polyethylene, which will provide the appropriate
strength at the lowest available cost. A typical application is the collation of
individual packs with or without tray support. The most frequent use of the forgoing
involves the packaging of a quantity of cans or bottles or cartons for distribution.
The equipment used involves a sleeve or bundle sealer working in conjunction with
a shrink tunnel. Two rolls of material produce a sleeve of film around the pack,
which is then processed through the tunnel. Generally, these open sleeves do not
cause any disadvantages to the pack integrity although a modification can be made
to the tunnel whereby an attempt is made to have the hole closed through excess,
annealed film.
A considerable amount of automation is offered for this process so that one may
find a full range of manual, semi and fully automatic sealers and at maximum through-put,
one can find lines with speeds of up to 200 packs per minute.
The processing of polyethylene is distinguished by the need for the film to reach
an almost melt state, after which cooling will provide significant additional shrink.
As a consequence, tunnels require specific cooling devices if elevated output speeds
are needed.
All of this equipment may be used to wrap individual packs where collation is not
required but a degree of protection is needed. Applications may vary from radiators
through to office doors and bolts of cloth.
The identical process is also applied but with display shrink film where products
have a natural requirement to use a sleeve. Gift wrap and wallpaper rolls fall into
this category. The principles remain the same although both the sealer and tunnel
will be modified to accommodate individual rolls with appropriately small diameters.
Turning to mainstream display applications, the main characteristic is the use of
a total wrap.
In every single case, the sealer must now create a flat, two-dimensional bag around
the product.
The product and this bag are then processed through a shrink tunnel to achieve the
desired effect.
At the most basic level, this is achieved using a L - Sealer and folded film. The product
is manually placed between the two layers of film and again manually placed into
the sealer. The seal is completed and the pack placed on the tunnel conveyor. This
is a continuous process that also produces an element of scrap film.
Automation is applied to the seal head and also to the pack support. Then, the seal
process and the removal of the pack to the tunnel become automated. Generally, this
is regarded as semi-automation. The clamping of the sealer head will be carried
out using either a solenoid or a pneumatic ram.
Full automation of an L - sealer will allow packs
to be automatically fed into the film and through to the sealer.
Over the last few years, there has been a general polarisation of the above
shrink wrap machinery into manual and fully automatic, with relatively few
machines being used in semi-automatic form. A manual machine will produce in the
order of 10 packs per minute whilst a fully automatic will produce in the order
of 20 packs per minute and there is relatively little speed advantage to be gained
from a semi-automatic sealer.
Costs also have a significant influence here since entry level equipment can be
purchased at significantly less than '2000.00 whilst fully automatic shrink wrap machinery
can be purchased at significantly less than '20,000.00.
The conventional use of a manual sealer and tunnel has been significantly reduced
by the use of combined seal & shrink machines , commonly
referred to as chamber equipment. These machines have a particularly small foot
print and operate generally from single phase. The sealer head incorporates a plastic
enclosure whilst heat is stored within the unit so that a combined seal and shrink
can take place.
The maximum output that can be achieved from a fully automatic L - sealer will be
in the order of 25-35 packs per minute.
As a consequence, both side seal and flow wrap machines are used to offer speeds
approaching 100 packs per minute. The methodology remains the same as ever - to
wrap the pack in a two dimensional bag of shrink wrap film.
Frequently, flat film is used although folded film is still applied by a number
of machines. The sealer will be able to process individual packs at a much higher
rate through the ability to seal at an appropriately higher rate.
Cross seals involve the seal device travelling with the pack whilst side seal or
overlap seal mechanisms allow for film to be sealed continuously.
These same machines may be applied to other bagging requirements - in particular
the mailing of magazines.
shrink wrap machinery can be specifically customised to take advantage of
any shrink wrap film's particular attributes to allow an appropriate pack to be
achieved. One example of the foregoing is the modification of this process to allow
for modified atmosphere
packaging of food using barrier shrink wrap film.
|
|
|
|
|
|
|
|
|
|
|
All Rights Reserved. © KEMPNER LIMITED 2008