|
The UK's largest distributor of display
shrink wrap and shrink wrapping machinery
|
Chamber/ Seal & Shrink Machines
» View
Shrink Wrap Machines
|
|
|
Shrink Wrap
Machinery | Shrink
Wrap Films |
Polyolefin Shrink Films
|
|
|
|
|
|
Shrink Wrap
> Shrink Wrap Films
> L - Sealers
L-Sealers
The purpose of this article is to allow the reader to understand the principles
that relate to the use of a L - sealer in creating a pack
enclosed within shrink film.
Shrink
wrapping requires a pack to be enclosed in shrink film before the pack and film
are introduced to a heat source which activates the film's memory to produce the
desired effect.
There are two ways in which pack may be wrapped - the pack may be either wholly
enclosed or partially enclosed using a sleeve.
The sleeve is not the concern of this article. Sleeve wrapping generally involves
polyethylene material and collations of packs where the medium provides the lowest
packaging costs for moving products in bulk.
The total enclosure of a pack allows it to be offered principally for display in
a thin material that enhances its appeal.
The issue is then to be able to create a bag around a product.
This is achieved either by a L - sealer or by an automatic
machine using one or two rolls of flat film where a variety of alternative sealing
methods leads to the same objective - the pack is wholly enclosed.
It is impossible to achieve an appropriate shrink result unless
the film is adequately secured around the product.
Hence, flat sheet film will not produce a shrink result.
There has been some work to offer shrink bags for the market.
These can be available in polyethylene but they are not available in either polyolefin
or PVC.
It is not possible to open bags to allow them to be used efficiently.
The consequence of these demands is that where production runs through either manual
or
semi-automatic equipment, a L - sealers is used.
The machine requires, then, that material is used that is centrefolded and presented,
on the reel.
Material is available in a variety of thicknesses and a variety of widths but the
common theme is that the material is presented to the sealer such that the reel
is unwound from the right to the left with the fold of the film at its rear.
The use of the expression L - sealer is marginally inaccurate
since sealing takes place using an inverted L.
The L-seal takes place such that the foot of the letter L is rotated through 180
degrees - the vertical axis of the L is unaltered but the base of the L is rotated
so that the foot points to the left and not the right.
The film is loaded onto the sealer and split in half using a splitter plate. This
allows one half of the film to pass underneath the plate and one half over the top
of the plate.
The adjustment of the width of the film together with the adjustment of the splitter
plate is made to accommodate the dimensions of the pack.
Before the first pack is introduced, the film is sealed for the first time.
The sealer works so as to cut the film and seal both sides of the cut.
The first cycle creates the left hand seal - and it is noted again that the film
is already effectively sealed at the rear by virtue of the film being folded in
half.
Having been inserted on the splitter plate, the pack and film are then moved into
the sealing area of the sealer.
The base of the sealer will also need to be adjusted for the height of the pack.
The pack is appropriately positioned and the film is also positioned to ensure a
minimum of creases and a lack of tension.
The sealing cycle creates the front seal - and scrap - together with the right hand
seal and as already mentioned, the left hand seal for the next pack.
As a consequence, the sealer may be continuously cycled to produce sealed packs.
The rate of scrap produced at the front of the pack requires to be optimised.
If there is too much, it is just uneconomic.
If there is too little, it is likely to cause slow production speeds together with
inadequate seal strength as the film is put under tension to ensure that it meets
on the seal beds at the front of the machine.
Although height adjustment is preferable, to allow seals to reside on the sides
of any pack, the true purpose is to minimise the film width.
It is essential that half the film covers the bottom of the pack and half its height
dimension and equally, half the film covers the top of the pack and half its height
dimension.
The fundamental principle remains the need to create two dimensional bags around
three dimensional objects.
L - sealing is most certainly also used on
fully automatic equipment where the same principles as above hold.
There are some variations with regard to accommodating the third dimension being
height.
At the simplest level, this is ignored.
At the more sophisticated level, the position of the seal head and beds is altered
to ensure that these components - rather than the pack - move to accommodate the
pack height.
It is worth highlighting the need to appreciate that plan sealing dimensions for
any L-sealer must be adjusted to account for pack height.
At their maximum, the length and width of any sealer must be reduced by half the
height of the pack to be wrapped.
Although an L-sealer can cope with an amount of film pleating, this will inhibit
a good quality seal.
As a consequence, film does require to be both flat as well as not under tension
on the seal beds. The key to successful L - sealing is the use of adequate temperature
and pressure with the complete absence of tension.
For automatic applications, shrink films require to have excellent machineability,
particularly with regard to tear resistance so that the film scrap may be continuously
removed from the sealer.
The selection of the correct material with the correct thickness and width is crucial
to successful L - sealing .
|
|
|
|
|
|
|
|
|
|
|
All Rights Reserved. © KEMPNER LIMITED 2008